Plumbing Basics: An Essential for When Installing a Bathtub
Plumbing Basics: An Essential for When Installing a Bathtub
Blog Article
Do you find yourself hunting for critical info concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably challenging job. If the old tub is conveniently accessible, the job can relocate immediately; if you have to open up a wall to get rid of the old tub and position the brand-new bath tub, the task is much harder. In either situation, the job is within a home handyman's abilities, although you will require a helper to leave the old tub and also set in the new one. See to it you have qualified on your own for the work as well as fit trying it. Rather than employing a contractor to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will certainly assist you set up a brand-new tub in your shower room if you have actually currently gotten a brand-new tub as well as don't need to transform the setup of your previous water supply pipelines.
Your devices as well as material checklist need to consist of the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome as a result of the limited accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this process. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The previous type should be connected to the tap finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the bath tub in the required position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the supply of water and also examine all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bath tub and also examine the overflow outlet as well as the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub should wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its last position.
Planning for the Installment
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, triggering the water to permeate the wall surface between the bathroom and the tiling, causing problems with moisture as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Remember to always fill the bath tub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can fracture rather early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is a good idea to fit the tiles using waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our section on How to Install a Bathtub. Thanks for taking the time to read our piece of content. Sharing is good. Helping others is fun. Many thanks for your time. Don't forget to visit our blog back soon.
Quick fix? We're here. Report this page